Asus kfsn4-dre manual

Refer to the ASUS contact information. Optional documentation Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. Page Typography Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual.

Page Chapter 1: Product Introduction This chapter describes the motherboard features and the new technologies it supports. Product introduction Page Welcome! Chapter summary Welcome! Page Welcome Before requesting support from the ASUS Technical Support team, you must take note of the motherboard's serial number containing 12 characters xxM0Axxxxxxx shown as the figure below. With the correct serial number of the product, ASUS Technical Support team members can then offer a quicker and satisfying solution to your problems.

Page Special Features Special features 1. This protection eliminates the need to buy a replacement ROM chip. Page 18 Chapter 1: Product introduction Page Chapter 2: Hardware Information This chapter lists the hardware setup procedures that you have to perform when installing system components.

It includes description of the jumpers and connectors on the motherboard. Hardware information Page 20 Chapter summary Before you proceed Page Motherboard Overview Place ten 10 screws into the holes indicated by circles to secure the motherboard to the chassis. DO NOT overtighten the screws! Doing so can damage the motherboard. Page Motherboard Layouts 2. Page 30 Press the load lever with your thumb A , then move it to the left B until it is released from the retention tab.

Retention tab PnP cap Load lever This side of the socket box should face you. Page 31 The CPU fits in only one correct orientation. Close the load plate A , then push the load lever B until it snaps into the retention tab. Page Installing The Heatsink 2. Make sure that you use only qualified heatsink assembly. Follow these steps to install the CPU heatsink. Place the heatsink on top of the installed CPU, making sure that the screw holes are matched with the heatsink standoffs.

Page Memory Configurations 2. Support the DIMM lightly with your fingers when pressing the retaining clips. Remove the DIMM from the socket. Page Expansion Slots Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support.

Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Removing the cap will cause system boot failure! Set to pins to activate the Gigabit LAN feature. Set the jumper to pins to enable the SAS function default. Make sure you download the correct BIOS for your motherboard model.

Page Connectors LED indications. Page Internal Connectors 2. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors!

The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. Each connector supports one device. Page 50 Page 51 This connector is for the locator button. This button queries the state of the system locator. Connect the Locator LED 2 cable to this connector. Page System Panel Connector Refer to the connector description below for details. It can also be used for building a high-powered workstation.

Powered by libreboot. This form factor is similar to E-ATX in that the size is identical, but the position of the screws are different. It is believed that 2MiB 16Mbits is the maximum size available for the flash chip. DO NOT hot-swap the chip with your bare hands. Use a PLCC chip extractor. These can be found online. Native graphics initialization exists XGI Z9s for this board. Framebuffer- and text-mode both work. Other revisions are believed to only support dual quad-core CPUs.

Note: not all CPUs are listed. The iKVM boards are so called because they offer a remote real-time access to the machine through a removable PCI management card, their hardware is the same as the non-iKVM ones. Note: the SAS functionality is not supported by osboot. There seems to be a 30 second bootblock delay observed by tpearson ; the system otherwise boots and works as expected.

This person says that they will look into it. The jitter disappears if using KMS once the kernel starts, but it will remain, if booting the kernel in text-mode.

This HTML page was generated by the untitled static site generator. Flashing instructions can be found at..